- #Can you upgrade cisco 2950 switch to gigabit ethernet update
- #Can you upgrade cisco 2950 switch to gigabit ethernet software
You use these interface configuration commands to configure them: In Cisco IOS 12.1EA, the Catalyst 2950 switch ranges for the IEEE 802.1x server-timeout, supp-timeout, and tx-period are 1 to 65535.
For more information, see Chapter33, “Configuring QoS”
With flow control, all traffic is stopped. You can configure QoS to restrict data traffic without affecting the control traffic. The Catalyst 2960 switch rejects the command, and this message appears: Switch(config-if)# The flowcontrol send command is not supported on the Catalyst 2960 switch. The Catalyst 2960 switch accepts received pause frames but cannot send them. You use this interface configuration command to configure it: The Catalyst 2950 switch supports pause frames on Gigabit Ethernet interfaces. It changes the maximum value to 2048 (if it is more than 2048), and this message appears: %Invalid input detected at ‘^’ marker.% The Catalyst 2960 switch accepts any range value. In Cisco IOS 12.2SE, the range was changed to 1 to 2048 messages per second. The range is 1 to 4294967294, and by default, the rate limit is not configured. The Catalyst 2960 switch rejects the command, and this message appears: Switch(config)#Ī Catalyst 2950 switch DHCP snooping feature limits the number of DHCP packets per second that an interface can receive. With the Catalyst 2960 switch, you can connect to candidate and cluster member switches through any VLAN in common with the cluster command switch. This command communicates the management VLAN when the switch is configured for clustering.
You can use this global configuration command to change it: The Catalyst 2950 switch supports only one management VLAN. The Catalyst 2960 switch rejects these commands, and this message appears: Switch(config)# When Cisco IOS 12.2E was restructured, these commands were intentionally removed and are not supported in Cisco IOS 12.2SE. These global configuration commands are in Cisco IOS 12.1EA: Table A-1 Catalyst 29 Switch Configuration Incompatibilities FeatureĬatalyst 2950 Switch Command and Explanation The features are listed in alphabetic order, with Catalyst 2950 commands and explanations, and the resulting action on the Catalyst 2960 switch. Table A-1 lists the Catalyst 2950 exceptions. In most cases, configuration files are loaded without rejections.
#Can you upgrade cisco 2950 switch to gigabit ethernet software
The Catalyst 2960 switch software handles the incompatible commands in these ways: If you use a Catalyst 2950 switch command, it might not be supported on the Catalyst 2960 switch. The switch families have different hardware.The Catalyst 2950 switch runs Cisco IOS 12.1EA software, and the Catalyst 2960 switch runs Cisco IOS 12.2SE software.The configuration commands between the two switch platforms differ for these reasons: This appendix consists of these sections: This appendix describes the configuration compatibility issues and the feature behavior differences that you might encounter when you upgrade a Catalyst 2950 switch to a Catalyst 2960 switch. Recommendations for Upgrading a Catalyst 2950 Switch to a Catalyst 2960 Switch Recommendations for Upgrading a Catalyst 2950 Switch to a Catalyst 2960 Switch.Unsupported Commands in Cisco IOS Release 12.2(58)SE.Working with the Cisco IOS File System, Configuration Files, and Software Images.Configuring EtherChannels and Link-State Tracking.Configuring Cisco IOS IP SLAs Operations.Configuring System Message Logging and Smart Logging.Configuring LLDP, LLDP-MED, and Wired Location Service.Configuring DHCP Features and IP Source Guard.
#Can you upgrade cisco 2950 switch to gigabit ethernet update
Configuring Flex Links and the MAC Address-Table Move Update Feature.Configuring Optional Spanning-Tree Features.Configuring IEEE 802.1x Port-Based Authentication.Configuring Switch-Based Authentication.Configuring Cisco IOS Configuration Engine.Assigning the Switch IP Address and Default Gateway.
0 kommentar(er)
